Let's Connect! Contacts
Let's Connect! Contacts

Let's connect!

Address*
Contact

ByTube Star 130 High-performance tube laser cutting

ByTube Star 130 - Title

Increase quality Fast and flexible tube laser cutting

Accelerate the laser cutting of tubes and profiles with the ByTube Star 130. Tube laser cutting with our high-end tube laser boosts the quality and performance in your production through:

  • Highest precision
  • Ease of use
  • Fully automatic setup of all profiles, including open and elliptical tubes

Fully automatic setup Also for open profiles and elliptical tubes

With the ByTube Star 130 you can process the full bandwidth from 10 to 130 mm. This also applies to open profiles. Without the operator´s manual intervention: 

  • There are no downtimes during the setup.
  • The fully automatic setup also increases the safety of your operators 
  • At the same time it reduces the risk of human error.

This leaves you more time for the essentials when tube laser cutting.

ByTube Star fully automatic tube laser cutting

More power Now with 4 kW

The new increased laser power of 4 kilowatts ensures an even faster cut. With this improvement, you can produce faster and more efficiently, increasing your productivity and competitiveness. This leads to an overall higher quality in tube laser cutting.

ByTube Star tube laser cutting QuickCut

Quick Cut Quality at high speed

An additional linear axis of the cutting head ensures highest speed and quality under all conditions. We also guarantee this for very small tubes.

Viteză mai mare, chiar și la tăierea profilului, cu funcția Tăiere rapidă.

Increase quality Fast and flexible tube laser cutting

Accelerate the laser cutting of tubes and profiles with the ByTube Star 130. Tube laser cutting with our high-end tube laser boosts the quality and performance in your production through:

  • Highest precision
  • Ease of use
  • Fully automatic setup of all profiles, including open and elliptical tubes

Fully automatic setup Also for open profiles and elliptical tubes

With the ByTube Star 130 you can process the full bandwidth from 10 to 130 mm. This also applies to open profiles. Without the operator´s manual intervention: 

  • There are no downtimes during the setup.
  • The fully automatic setup also increases the safety of your operators 
  • At the same time it reduces the risk of human error.

This leaves you more time for the essentials when tube laser cutting.

More power Now with 4 kW

The new increased laser power of 4 kilowatts ensures an even faster cut. With this improvement, you can produce faster and more efficiently, increasing your productivity and competitiveness. This leads to an overall higher quality in tube laser cutting.

Quick Cut Quality at high speed

An additional linear axis of the cutting head ensures highest speed and quality under all conditions. We also guarantee this for very small tubes.

ByTube Star fully automatic tube laser cutting
ByTube Star tube laser cutting QuickCut
Viteză mai mare, chiar și la tăierea profilului, cu funcția Tăiere rapidă.

Your simple entry into tube laser cutting. Learn more about our ByTube Star 130.

Technical specifications

Technical specifications All information on the ByTube Star 130

 ByTube Star 130
Min. Tube length (with automatic loading)8.2 ft
Max. Tube length21 – 28 ft
Max. Tube weight11 lb/ft
Tube sectionsO ◻ ▯ ⬭ U C L —
Dimensions round sections (min. – max.)Ø 0.375 – 5.1 in
Dimensions rectangular sections (min. – max.)0.375 x 0.375 – 5.1 x 5.1 in
Dimensions other closed sections (min-max length of the sides)0.375 x 0.375 – 5.1 x 5.1 in
Dimension flat bars1.5 – 5 in
Thickness flat bars0.2 – 0.59 in*
Max. linear speed of axis X / Y / Z656.16 / 196.8 / 196.8 ft/min
 
Max. rotation speed of mandrels250 r.p.m.
Max. piece length unloading system6.56 – 13.12 - 20 ft
X, Y and Z axis positioning precision**± 0,003 in
Number of controlled axis8
Machine weight***22 046.2 lbs
Numeric ControlBySoft Cell Control Tube

Laser sources for the ByTube Star Tube laser cutting with up to 4 kilowatts of laser power

The ByTube Star 130 tube laser cutting machine eliminates the need for time-consuming drilling, sawing, milling, or punching. The increased laser power and the optimized cutting process allows you fast, automated and precise cutting:

  • Closed tubes
  • Angles
  • Channels
  • Flat bars
  • Ellipses

Our specialists for tube laser cutting machines are happy to advise you.

Features

Features and options

  • Productivity & Efficiency
  • Quality
  • Flexibilty
  • Simplicity
  • Future Fit
  • Peace of Mind
  • Business Success

Fully automatic set-up (incl open sections)

No downtime for set-up means more time for cutting, so more productivity.

4kW fibre laser

Higher speed, regardless of the type of material, material thickness or size. 

Quick Cut – Performance mode

Maximum cutting performance for maximum productivity. The combination of movements of cutting head and tube achieves the highest acceleration values to reach the maximum cutting performance.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Active tube support during cutting process

The tube support by controlled axis both in the loading and in the unloading helps to keep the tube straight. Accuracy is guaranteed even with long tubes.

4kW fibre laser

The database of cutting parameters enables us to achieve the best performance and quality for different materials and material thicknesses. 

Laserscan

Real-time compensation of tube bending enables high cutting accuracy, even with low-quality material.

Quick Cut – Quality mode

Small geometries, no vibrations and increased cutting quality - the head can machine tubes without repositioning.

Parameters for brass and copper + safety

More cutting possibilities with a complete set of parameters. The copper and brass package consists of a database of cutting parameters and the safety systems. In addition, the operator is protected from possible back reflections.

Bundle loader

A simple device that is straightforward to set up. Using the bundle loader, you can load bundles of tubes, single bars or open sections.

Conveyor belts for cut parts

Conveyor belts collect parts after cutting and give the operator sufficient time for logistics, packaging or carrying out other tasks. The parts fall directly into boxes or pallets.

Open sections

The ByTube Star 130 can process not only closed tubes, but also angles, channels and flat bars - no set-up required.

Fully automatic set-up (incl. open sections)

Whenever a change of production is required, the operator just has to load the material, run the program and start the machine. This makes ByTube Star 130 not only easy to operate. It is also suitable for entry-level users in the tube business.

HMI / ByVision Tube

The ByVision Tube user interface enables intuitive operator guidance via a touch screen. It’s optimally tailored to Bystronic’s machine systems and supports the entire range of applications.

Weld seam search camera

The automatic detection of the weld seam position on tube inner surface is needed for many applications, especially when tube is bent after cutting

Laserscan

High accuracy is ensured in all cutting conditions with low impact on process speed. This reduces the quality assurance work required for cut parts. 

Fully automatic set-up (incl. open sections)

Machine is ready for the future, because connection with storage and/or sorting devices is facilitated by the fully automatic set-up for every tube or profile. 

Bundle loader

Bundle loader is easily accessible for the manual loading of bundles. It is also suitable for easy connection with storage devices. Continuous loading of tubes is guaranteed, minimising downtime, logistics work, and reducing the risk of operator errors.

HMI / ByVision Tube

The ByVision Tube user interface enables intuitive operator guidance via a touch screen. It is optimally tailored to Bystronic’s machine systems and supports the full bandwidth of applications.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Fully automatic set-up (incl. open sections)

Less risk of operator errors and enhanced safety for the operators.

Cutting head

The cutting head is fibre laser technology “made by Bystronic”. This means less work for service teams and purchasing.

Laserscan

Always guarantees high accuracy in all cutting conditions, even with low-quality material. 

Quick Cut – Quality mode

Holes and other features always cut with perfect quality even in difficult conditions. This results in less waste and fewer rejects.

Fully automatic set-up (incl. open sections)

Downtime as a consequence of manual machine set-up is drastically reduced thanks the fully automatic set-up. This results in more throughput and lower cost per part. 

4kW fibre laser

Maximum productivity thanks to the highest power available for a small tube laser. The best cut quality on thick materials.

Open sections

The ByTube Star 130 processes more than standard tubes. It can also handle angles, channels and flat bars.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Productivity & Efficiency

Fully automatic set-up (incl open sections)

No downtime for set-up means more time for cutting, so more productivity.

4kW fibre laser

Higher speed, regardless of the type of material, material thickness or size. 

Quick Cut – Performance mode

Maximum cutting performance for maximum productivity. The combination of movements of cutting head and tube achieves the highest acceleration values to reach the maximum cutting performance.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Quality

Active tube support during cutting process

The tube support by controlled axis both in the loading and in the unloading helps to keep the tube straight. Accuracy is guaranteed even with long tubes.

4kW fibre laser

The database of cutting parameters enables us to achieve the best performance and quality for different materials and material thicknesses. 

Laserscan

Real-time compensation of tube bending enables high cutting accuracy, even with low-quality material.

Quick Cut – Quality mode

Small geometries, no vibrations and increased cutting quality - the head can machine tubes without repositioning.

Flexibilty

Parameters for brass and copper + safety

More cutting possibilities with a complete set of parameters. The copper and brass package consists of a database of cutting parameters and the safety systems. In addition, the operator is protected from possible back reflections.

Bundle loader

A simple device that is straightforward to set up. Using the bundle loader, you can load bundles of tubes, single bars or open sections.

Conveyor belts for cut parts

Conveyor belts collect parts after cutting and give the operator sufficient time for logistics, packaging or carrying out other tasks. The parts fall directly into boxes or pallets.

Open sections

The ByTube Star 130 can process not only closed tubes, but also angles, channels and flat bars - no set-up required.

Simplicity

Fully automatic set-up (incl. open sections)

Whenever a change of production is required, the operator just has to load the material, run the program and start the machine. This makes ByTube Star 130 not only easy to operate. It is also suitable for entry-level users in the tube business.

HMI / ByVision Tube

The ByVision Tube user interface enables intuitive operator guidance via a touch screen. It’s optimally tailored to Bystronic’s machine systems and supports the entire range of applications.

Weld seam search camera

The automatic detection of the weld seam position on tube inner surface is needed for many applications, especially when tube is bent after cutting

Laserscan

High accuracy is ensured in all cutting conditions with low impact on process speed. This reduces the quality assurance work required for cut parts. 

Future Fit

Fully automatic set-up (incl. open sections)

Machine is ready for the future, because connection with storage and/or sorting devices is facilitated by the fully automatic set-up for every tube or profile. 

Bundle loader

Bundle loader is easily accessible for the manual loading of bundles. It is also suitable for easy connection with storage devices. Continuous loading of tubes is guaranteed, minimising downtime, logistics work, and reducing the risk of operator errors.

HMI / ByVision Tube

The ByVision Tube user interface enables intuitive operator guidance via a touch screen. It is optimally tailored to Bystronic’s machine systems and supports the full bandwidth of applications.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Peace of Mind

Fully automatic set-up (incl. open sections)

Less risk of operator errors and enhanced safety for the operators.

Cutting head

The cutting head is fibre laser technology “made by Bystronic”. This means less work for service teams and purchasing.

Laserscan

Always guarantees high accuracy in all cutting conditions, even with low-quality material. 

Quick Cut – Quality mode

Holes and other features always cut with perfect quality even in difficult conditions. This results in less waste and fewer rejects.

Business Success

Fully automatic set-up (incl. open sections)

Downtime as a consequence of manual machine set-up is drastically reduced thanks the fully automatic set-up. This results in more throughput and lower cost per part. 

4kW fibre laser

Maximum productivity thanks to the highest power available for a small tube laser. The best cut quality on thick materials.

Open sections

The ByTube Star 130 processes more than standard tubes. It can also handle angles, channels and flat bars.

Preparation for N2 generator

Stay independent of your gas provider and ensure a consistent supply of gas and cutting quality.

Videos

Videos Complete package for a quick entry into tube laser cutting

With the ByTube Star 130 you benefit from numerous services in just one machine:

  • Fully automatic setup 
  • User-friendly interface
  • Enhanced speed
  • Improved cutting precision
ByTube Star 130 thumbnail

Highlights from the video

ByTube Star 130 tube laser cutting easy start

Get started easily

Tried-and-tested technology and a user-friendly interface facilitate your first steps into the world of tube laser cutting. 

ByTube Star fully automatic tube laser cutting

Fully automatic setup

Process the full range of tubes, ellipses, and profiles with sizes from 10 to 130 mm.

Viteză mai mare, chiar și la tăierea profilului, cu funcția Tăiere rapidă.

Quick Cut feature

An additional linear axis of the cutting head delivers maximum speed and quality under all cutting conditions.

ByTube Star 130 tube laser cutting laserscan

Laserscan feature

The real-time compensation of tube deflections further enhances the precision during the tube laser cutting process.

Video tutorials

Service

Bystronic Service Tailor-made for your needs and smooth production

Comprehensive service packages from ByCare, including tailor-made service packages for all your maintenance needs.

ByCare packages

Our trained service experts ensure efficient production processes and safety for your employees. Depending on the requirements, we offer packages with basic to all-around services.

preventice maintenance and proactive advice from the expert

360° Customer Advisor

We analyze your production and determine your strengths and weaknesses. Based on this information, you can optimize processes and decrease downtime.

Bystronic employees providing after sales and service by reviewing a cut sheet metal part.

Our services

We maintain and repair your Bystronic systems. Optionally, you can obtain upgrades to retrofit your system or accessories to fine-tune your solution. Upon request, we can also perform a general overhaul.

Our service experts are always there for you – quickly and in person

Software

Software for your tube laser BySoft Cell Control Tube: Convenient guidance through the tube laser cutting process

Simplify the tube laser cutting process with our software. Every function on the touch screen is simple to understand. From the visualization of parts right through to the monitoring of the production process – the correct settings are selected in a fast and simple workflow.

BySoft Cell Control Tube for ByTube Star 130 tube laser cutting

BySoft Suite for networked production Software for efficient processes

The future of sheet processing lies in intelligent production. In order to master these challenges, Bystronic has developed a trend-setting software. It enables your company to optimally control your production. By networking all areas, the software offers seamless communication and efficient control of all processes. 

Let Bystronic lead you into the digital future of tube laser cutting.

Learn more
Jeszcze bardziej cyfryzuje branżę obróbki blach i zapewnia uproszczenie, przejrzystość i wydajność: całkowicie nowy pakiet BySoft Suite.